|
|
 FAQ
 Search
 Memberlist
 Usergroups
 Register
 Profile
 Private messages
 Log in
|
|
| Author |
Message |
JM
Guest
|
 Posted: Sat Apr 29, 2006 9:50 pm Post subject: Need help with Lantronix device |
 |
|
I have taken in some Lantronix ETS16P terminal server devices, and I am
trying to determine if they are in good working order. My understanding is
that they are out of service working, but I cannot get them to respond. I
highly suspect user error.
I downloaded the documentation, and I have tried 2 different ways to
configure: the Lantronix EZWebCon software and using a console cable (the
type I use with Cisco routers) and HyperTerminal. Using the former, it does
not show up in the "devices" window after it searches the network (then
again, nothing is showing up there). Using Hyperterminal, it doesn't
respond to the Return key.
The lights on the front show power, a steady link light, and occasional
blink of the network light. I have a straight through network cable from my
router into the rj45 ethernet connection on the back of the ETS. I know the
cable to be good, and the router is giving out IPs.
Does anyone here have experience with these things?
thank you,
jm |
|
| Back to top |
|
 |
|
|
Scooby
Guest
|
| Posted: Sat Apr 29, 2006 10:50 pm Post subject: Re: Need help with Lantronix device |
|
|
"JM" <jm@yahoo.com> wrote in message
news:VnQ4g.22463$mh.17546@tornado.ohiordc.rr.com...
| Quote: | I have taken in some Lantronix ETS16P terminal server devices, and I am
trying to determine if they are in good working order. My understanding is
that they are out of service working, but I cannot get them to respond. I
highly suspect user error.
I downloaded the documentation, and I have tried 2 different ways to
configure: the Lantronix EZWebCon software and using a console cable (the
type I use with Cisco routers) and HyperTerminal. Using the former, it
does not show up in the "devices" window after it searches the network
(then again, nothing is showing up there). Using Hyperterminal, it
doesn't respond to the Return key.
The lights on the front show power, a steady link light, and occasional
blink of the network light. I have a straight through network cable from
my router into the rj45 ethernet connection on the back of the ETS. I
know the cable to be good, and the router is giving out IPs.
Does anyone here have experience with these things?
thank you,
jm
|
JM,
I've worked a fair amount with these in the past. Still have them, but they
are very low maintenance and haven't had to do much with them lately. They
are probably working since you see the indicators that you do. The easiest
way to figure out how to connect would be to put a packet sniffer on it and
see what address it arps out or if it is getting its ip from dhcp. Then,
you can telnet to it. But, if there is a password, you are stuck. You'll
need that with the cable as well.
Go back and read the manual again. There probably is a way to factory
reset. Once you have done that, they have directions for connecting by
tcp/ip without needing the console cable. Also, they have instructions for
making a cable. I don't believe that the Cisco cables work - I never used
these with my Cisco equipment, so not quite sure on that one. I've always
just had caps made that you can use with a regular cat5 cable.
Worst case, email the tech support at Lantronix. Even if you don't have a
support agreement with them, they'll probably respond to you. They've
always been very helpful to me in the past.
Hope that helps,
Jim |
|
| Back to top |
|
|
News 2 Me
Guest
|
| Posted: Sun Apr 30, 2006 4:50 pm Post subject: Re: Need help with Lantronix device |
|
|
JM wrote:
| Quote: | I have taken in some Lantronix ETS16P terminal server devices, and I am
trying to determine if they are in good working order. My understanding is
that they are out of service working, but I cannot get them to respond. I
highly suspect user error.
I downloaded the documentation, and I have tried 2 different ways to
configure: the Lantronix EZWebCon software and using a console cable (the
type I use with Cisco routers) and HyperTerminal. Using the former, it does
not show up in the "devices" window after it searches the network (then
again, nothing is showing up there). Using Hyperterminal, it doesn't
respond to the Return key.
The lights on the front show power, a steady link light, and occasional
blink of the network light. I have a straight through network cable from my
router into the rj45 ethernet connection on the back of the ETS. I know the
cable to be good, and the router is giving out IPs.
Does anyone here have experience with these things?
|
I am currently using single-port servers from Lantronix (MSS-1/100 and
UDS-10/100). As Scooby pointed out, you're going to need to do a
factory default on them. The manual should tell you how to do this. On
the MSS and UDS models, you insert the end of a straightened out paper
clip into a small hole in the case that has a push button behind it,
then power it up with the button depressed, keeping it depressed for
five seconds or so.
After a factory default, both the MSS and UDS models will try assigning
an IP address (and possibly booting) via BOOTP, DHCP and RARP. I don't
remember what order it tries these in, but it sounds like your router is
a acting as a DHCP server, so it should assign an IP to the terminal
server after a default.
I haven't been too impressed with either EZWebCon or DeviceInstaller. I
prefer to use the command line interface via telnet. The web interface
isn't bad, but that doesn't work until the unit is minimally configured
via DHCP/RARP/BOOTP or the command line.
What kind of cable did you use with Hyperterm? The MSSes that I use are
DTEs, so a null-modem cable is required to connect to a PC. The UDSes,
are DCEs, so a straight-thru cable is required to connect to a PC.
The manual should tell you what you have.
NM |
|
| Back to top |
|
|
|
|
